Pilots shall be prepared to immediately disengage the autopilot, should any unscheduled ________ be evident. An autopilot lateral malfunction can result in bank angles of _____ deg within ____ sec even though recovery is started approximately ____ sec after the malfunction occurs. A pitch up malfunction could cause a stall within ___ seconds and is therefor considered the most serious autopilot malfunction.

Answer: control movement; 55; 5; 3; 3

Since low outside air temperature causes a considerable increase in thrust, the ________________ limitations may be reached with somewhat lower throttle settings.

Answer: airplane operating

During operation at low gross weight, and particularly at low ambient temperature, the airplane accelerates very rapidly; therefor care should be taken to not exceed the ______ during flap retraction.

Answer: placard speeds

If the airplane fails to pressurize, ensure the cabin test valve handle is in the ______ position.

Answer: Normal

(Cargo door opening after Takeoff) If conditions permit, maintain a flap setting of ______deg, this will retain the use of outboard ailerons for roll control

Answer: 20 deg

Opening of the cargo door during or after takeoff will be noted by illumination of the _________ and will probably cause severe ________

Answer: Door Warning Light; Airplane buffeting

If during a climb all airspeed indicators are determined to be inaccurate, continue max climb thrust and maintain ____ deg of pitch on the ADI for gross weights up to 225K. Maintain ____ deg pitch for gross weights greater than 225K.

Answer: 8; 6

To determine which airspeed indicator is most accurate, the aircraft should be flown with wings level so that the speed deviation pointer indicates _______ (0.6 AOA) and the airspeed reading at ).6 AOA should compare with the corresponding airspeed, for the aircraft weight and configuration obtained from the 1-1.

Answer: "On speed"

If there is a disparity between airspeed indicators, the ____________ may be used to determine which indicators are most accurate

Answer: speed deviation indicators

For nose up trim, set the inboard spoiler switch to CUT-OUT. This configuration provides approx. ______ units of equivalent trim in takeoff configuration

Answer: 2-3

If a stabilizer trim runaway occurs at or below S1, simultaneously the pilot flying will ______ and the pilot not flying will ____________

Answer: abort the takeoff; set stab trim to cutoff

If the leading edge flaps fail to retract when the outboard flaps are raised above the 6 deg position and the outboard spoiler switch is in NORMAL, you should ___________

Answer: move the outboard spoiler switch to CUT-OUT

Do not operate the _________ and the ________ simultaneously. Slow operation of the ______ and reduced climb performance will result.

Answer: Forward A/R pumps; Landing gear

When the main flaps are retracted and one or both leading edge flaps remain extended, the airplane should be flown with caution at load factors in excess of 1.5 g's in the speed range between ____ and _____ kts.

Answer: 214;305

If all means of flap synchronization fail and conditions permit, institute ________(if required) and land as soon as possible.

Answer: fuel dumping

If the flap indicators or visual inspection reflect an asymmetric main flap condition and a rolling moment is present, the flap lever should be set to the ____________

Answer: Asymmetric flap position indication

Most lateral and directional control difficulties are associated with __

Most lateral and directional control difficulties are associated with _______, ________, ________, ________ or flight control malfunctions.

Answer: Engine, A/P, EFAS, YD.

Takeoff should not be attempted if the oil pressure is more than ______ psi. Bearing failure die to plugged oil jets can result.

Answer: 92

Throttle reduction in response to a failed engine/engine flameout during takeoff or initial climb out after takeoff should not be made prior to ______________

Answer: landing gear retraction

If a catastrophic engine failure occurs accompanied by a fire, take prompt action to pull fire switch and discharge extinguishing agent. Failure to accomplish these actions promptly can result in loss of _______ controls due to burned electrical wiring bundle.

Answer: Fire Switch